Results 1 to 10 of 10

Thread: eric113's portal axle JK

  1. #1
    Senior Member eric113's Avatar
    Join Date
    Aug 2008
    Location
    Kyle
    Posts
    1,210

    eric113's portal axle JK

    Current Setup

    Front Axle
    Axial HD locker
    3racing portal
    Traxxas stub shafts *Need to send to chino63
    Gunnar custom pins *Need to install
    Custom steering links *Need to buy and make
    Axial Cvd's * Need to install
    STRC clockable C's
    Axial stock gears * Need to regrease


    Rear Axle
    Axial HD lockers
    Axial Stock gears * Need to regrease
    3racing lock out
    3racing portal
    Traxxas stub shafts *Need to buy
    Gunnar custom pins *Need to install
    Axial 4 link mount
    Axial stock inner shafts


    Rolling Stock
    Rc4wd Hummer wheels
    Axial treps or custom 4.75" super swampers. *Need to sipe swampers

    Transmission
    Gunnar idler pin
    Axial steel ouputs
    Axial stock motor plate
    16 tooth 48 pitch Robinson Racing pinion
    80 tooth 48 pitch kimbrought Spur Gear

    Driveshafts
    Axial W8B driveshafts
    Gunnar pins
    Driveshaft mod *Need to do

    Suspension
    Axial aluminum lower links
    Traxxas steel push rods rear uppers
    Axial stock scx10 shocks

    Chassis and Body
    Axial Scx10 chassis
    Hand Bro's Scx10 CMS plate
    Rc bros servo clamps
    Axial Jeep JK body
    Axial stock JK front bumper
    Axial stock JK rear bumper
    Stock Axial hardware
    Fattbatt electronics/winch tray

    Power and Control
    Holmes Hobbies waterproof BRXL ESC
    Castle Creations BEC set @ 7v
    Holmes Hobbies TrailMaster Sport 540
    Futaba S9156 steering servo
    Dynamite alum servo horn
    Futaba 4PK
    Futaba R604FS RX
    Towerpro 945MG servo winch
    Heyok HV winch controller
    QuickSand winch
    Tekin B1R esc winch controller *Need to buy
    1300mah 40c 4s sky lipos
    Last edited by eric113; 07-30-2013 at 03:04 PM.

  2. #2
    Senior Member eric113's Avatar
    Join Date
    Aug 2008
    Location
    Kyle
    Posts
    1,210
    Inspiration came from Google search and after seeing all the Axial Jeep JK's pop up.










  3. #3
    Senior Member eric113's Avatar
    Join Date
    Aug 2008
    Location
    Kyle
    Posts
    1,210
    I traded my first JK and started to miss it, made another trade.

    Here go again and this one is to stay! It stock jk kit, brand new.

    So far I added the portals and Traxxas steel push rods for the rear upper links. I'm not going super crazy with mods. Mostly stock with few upgrades.

    Future plans:
    Locked up lockers
    R2j sliders
    Corner guards






    I still have bunch little stuff to do.


  4. #4
    Administrator sgtsteve's Avatar
    Join Date
    Sep 2008
    Location
    Georgetown, TX
    Posts
    2,214
    Mr Portals strikes again! Good to have ya back Eric:SpicyPBJ:


    Team Manager
    - SCALE PERFORMANCE PARTS -




  5. #5
    Senior Member eric113's Avatar
    Join Date
    Aug 2008
    Location
    Kyle
    Posts
    1,210
    Thanks Steve! I did work on it tonight. Got bunch small stuff done.

    -Installed gunnar pins in the driveshafts
    -Mounted the quicksand winch with a plate I made under
    -Installed non slipper with 80t spur and 18t pinion
    -Regreased the trans
    -Swapped out lower link rod ends to Traxxas and stainless steel set screws
    -lowered the windsheild







    Wheel works black & tacky
    Last edited by eric113; 07-30-2013 at 08:57 PM.

  6. #6
    Administrator sgtsteve's Avatar
    Join Date
    Sep 2008
    Location
    Georgetown, TX
    Posts
    2,214
    Looks like its ready to roll for Rock the Night, this Saturday night:mrgreen:


    Team Manager
    - SCALE PERFORMANCE PARTS -




  7. #7
    Senior Member eric113's Avatar
    Join Date
    Aug 2008
    Location
    Kyle
    Posts
    1,210
    Not even close.:cry:

  8. #8
    Senior Member eric113's Avatar
    Join Date
    Aug 2008
    Location
    Kyle
    Posts
    1,210
    One wheel and tire done. 3 more to go...:Shaking:





    Last edited by eric113; 07-31-2013 at 10:12 AM.

  9. #9
    Administrator sgtsteve's Avatar
    Join Date
    Sep 2008
    Location
    Georgetown, TX
    Posts
    2,214
    Love the hummer wheels on there Eric! I looked for rod ends but don't have any.


    Team Manager
    - SCALE PERFORMANCE PARTS -




  10. #10
    Senior Member eric113's Avatar
    Join Date
    Aug 2008
    Location
    Kyle
    Posts
    1,210
    Thanks for looking Steve.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •