PDA

View Full Version : Well Here she is



jcsaxial
05-03-2012, 04:48 PM
Still need to get elect installed and metal tierod and draglink. Workin w a hitek 645 and it just doesnt have enough power so those will be the next purchases:brickwall:

http://i1215.photobucket.com/albums/cc511/jeremysaxby/015.jpg
http://i1215.photobucket.com/albums/cc511/jeremysaxby/014.jpg

bbking9
05-03-2012, 04:54 PM
Looks great. I do like the red rings.

jcsaxial
05-03-2012, 05:15 PM
I did notice that the wheels dont fit real well on the hexes but they do hold

bbking9
05-03-2012, 05:19 PM
Thats odd...

Tremelle
05-03-2012, 05:45 PM
I did notice that the wheels dont fit real well on the hexes but they do hold

What is it that seems to be the problem? Are the hubs worn or is the hub on the rim worn?

jcsaxial
05-03-2012, 06:02 PM
They dont seem to be going all the way on. The wheels are brand new i think the end of the hex is preventing them but im not about to drill them out. I could and pit the washer on like my ther 2.2s but we see what happens. Ill have to get w yall next week to check it out

jcsaxial
05-03-2012, 08:35 PM
i cant get good pis of it but here it is
http://i1215.photobucket.com/albums/cc511/jeremysaxby/022-1.jpg
http://i1215.photobucket.com/albums/cc511/jeremysaxby/019.jpg
http://i1215.photobucket.com/albums/cc511/jeremysaxby/018.jpg
http://i1215.photobucket.com/albums/cc511/jeremysaxby/017.jpg
http://i1215.photobucket.com/albums/cc511/jeremysaxby/026.jpg

I may have to shave the end off the hex to make them sit right

jcsaxial
05-03-2012, 08:49 PM
Well thats not it, I think they are the wong hexes all around. bully wheels so im guessin i need bully hexes thaught they were the same

Locked Up
05-03-2012, 08:57 PM
Dremel.

You can dremel the little end off the hex and they should be fine.
:thumbsup:

STANG KILLA SS
05-03-2012, 09:01 PM
yeah axial hexes have that little nipple for some stupid reason. sand them off and your good to go.

Tremelle
05-03-2012, 09:02 PM
I could not quite tell from the pics, but it appears the hexs are wider than the wheel hub mount. I have some hubs that are wide to give a wider track width, and the back of the hex sticks out the wheel hub.

jcsaxial
05-03-2012, 09:05 PM
nope just looked them up and they are 12mm so i need to find some

bbking9
05-03-2012, 10:58 PM
Sand the nipple - sounds a little rough !!!

jcsaxial
05-04-2012, 08:33 PM
just picked up some traxxas 12mm hexes be installed mon

burnitup
05-05-2012, 07:18 PM
hey jc, i think it might look and run a bit stronger if you'd stretch out the rear a bit.
i may be wrong, but give it a try:thumbsup:

jcsaxial
05-07-2012, 05:03 PM
Well i have renamed "BUDlIGHT TYME" to PAPA SMURF and yall know papa smurf was a pimp! lol I guess its the red rings white pannels and blue frame.